Computer

Computer Fundamentals

Computer Networking

Data Structure

Information Technology

Programming Languages



Comments

Post a Comment

Popular posts from this blog

Material Science Quiz (Mechanical Properties of Metals)

1. Time dependent permanent deformation is called ________________. (a) Plastic deformation (b) Elastic deformation (c) Creep (d) Anelastic deformation 2. Figure-out the odd point in the following (a) Proportinal limit (b) Elastic limit (c) Yeild point (d) Fracture point 3. If a material is subjected to two incremental true strains namely ε1 and ε2, then the total true strain is (a) ε1 * ε2 (b) ε1 - ε2 (c) ε1 + ε2 (d) ε1 / ε2 4. Engineering stress-strain curve and True stress-strain curve are equal up to (a) Proportional limit (b) Elastic limit (c) Yeild point (d) Tensile strength point 5. Value of Poisson’s ratio for ionic solids in the range of (a) 0.1 (b) 0.2 (c) 0.3 (d) 0.4 6. Hydrostatic stress results in the following (a) Linear strain (b) Shear strain (c) Both linear and shear strains (d) None 7. High elastic modulus in materials arises from (a) High strength of bonds (b) Weak bonds (c) combination of bonds (d) None 8. Change in elastic modulus for ordinar
Read more

Material Science (Corrosion & Degradation of Materials)

1.         Corrosion of metals involves (a) Physical reactions (b) Chemical reactions (c) Both (d) None 2.         The following factors play vital role in corrosion process (a) Temperature (b) Solute concentration (c) Both (d) None 3.         Following equation is related to corrosion rate (a) Nernst equation (b) Faraday’s equation (c) Either (d) Neither 4.         Passivity is due to (a) Higher EMF (b) Lower EMF (c) Oxide film (d) All 5.         Passivity is not reason for inertness of the following (a) Au (b) Al (c) Ti (d) Ni 6.         Difficult to monitor and very dangerous form of corrosion (a) Galvanic (b) Pitting (c) Crevice (d) Stress 7.         This form of corrosion occurs due to concentration difference in a component (a) Uniform (b) Galvanic (c) Inter-granular (d) Stress 8.         Main form of ceramic degradation (a) Corrosion (b) Weathering (c) Dissolution (d) Swelling 9.         The following influences deterioration of p
Read more

Material Science Quiz (Failure)

1. Failure due to excessive deformation is controlled by ______________. (a) Material properties (b) Design & Dimensions (c) Both (d) None 2. Failure due to excessive deformation is controlled by ______________. (a) Yield strength (b) Tensile strength (c) Young’s modulus (d) All 3. Time dependent yield is known as (a) Fracture (b) Fatigue (c) Buckling (d) Creep 4. Cleavage fracture appears (a) Bright (b) Dull (c) Difficult to identify (d) None 5. Usually materials with following crystal structure fail in ductile mode (a) FCC (b) BCC (c) HCP (d) None 6. Brittle fracture is more dangerous than ductile fracture because _______________. (a) No warning sign (b) Crack propagates at very high speeds (c) No need for extra stress during crack propagation (d) All 7. Fracture voids usually form at (a) Inclusions (b) Second phase particles (c) Grain boundary triple points (d) All 8. Fracture stress (σf) is proportional to (a) crack length (b) 1/crack length (c) (crac
Read more